3 phase permanent magnet alternator. Max 10-14 dBA above background. Description of Battery Charge Controller. Wind Turbine automatically braking voltage.Recovery time after the automatic braking. Voltage Regulation Set Point(factory setting) 12 Volt Systems 14.1 Volts 24 Volt Systems 28.2 Volts 48 Volt Systems 56.4 Volts. Regulator Adjustment Range 12 Volt Systems 13.6 Volts to 17.0 Volts(approximately) 24 Volt Systems 27.2 Volts to 34.0 Volts(approximately) 48 Volt Systems 54.4 Volts to 68.0 Volts(approximately). Recommended Fuse Size 12 Volt Systems 50 amp(slow blow) 24 Volt Systems 25 amp(slow blow) 48 Volt Systems 15 amp(slow blow).
Your wind turbine will be delivered partially assembled. The blades on the blade hub. Securing the hub to the turbine body and. Installing the nosecone on the blade hub. The necessary hex key (Allen).
Wrenches are furnished with wind turbine. Start the assembly by mounting the blades to the blade hub as shown in upon. Place a nylock nut in the hexagonal detent on the back of the blade hub while positioning the blade on the hub. The blades must be tilted into position on the hub and can only be installed in one orientation.Place a washer on a 1/4 - 20 socket head screw and. Coat the screw threads with Tef-Gel. Pass the screw through the base of. The blade and screw it into the nylock nut.
Tighten the screw to 10 ft-lbs. Repeat for the remaining two blades. Nylock nuts may only be.
Used one time; replace after each use. Wind Turbine Siting Small changes in wind speed can have a dramatic effect on power production. The siting of your wind turbine should be carefully considered. Each installation is different and is often a compromise among tower height.
Distance from the battery bank, local zoning requirements and obstacles such as buildings and trees. In general the higher the tower, the greater the wind speed and ultimately power production. However, towers are expensive and can easily exceed the cost of the turbine. The minimum recommended tower height is 25 ft (7.6 m) on open ground or 20 ft (6 m) above nearby obstructions. Try to locate the wind turbine in the cleanest turbulent free air as possible.
Turbulence will reduce the efficiency of the wind turbine and may accelerate wear on rotating component. Safety must be the primary concern when selecting the mounting location i nstall Wind turbine. So there is no possibility of accidental contact with rotating blades even if it requires installing it in a less than ideal location.Safety has precedence over efficiency. Wind Turbine Towers (Not include) The wind turbine is designed to mount on tubing or pipe with a nominal 48-50 mm outside diameter. Under no circumstances should plastic pipe be used to construct a tower.
Wind Turbine Wiring Options The recommended way to connect the turbine to your battery bank is to wire the turbine directly to its own set of battery posts through a charge controller. This will allow the turbine to operate independently. The controller will monitor the battery and maintain the charge as necessary.Wire Size All electrical systems lose energy due to resistance in conductors: the wires. Large wires have less resistance but can be considerably more costly. Resistance losses will also increase with increasing current, therefore, if yours is a high wind site. It may be worthwhile to go with a larger size wire to take advantage of the greater power production potential of your site. Conversely, in low wind sites it may not be cost effective to increase the wire size since power production will be low. The following wiring sizes provide maximum annual energy losses of 5% or less for sites with a 4.2m/s average wind speed. Which is sufficient for most sites. To determine the size wire, measure the distance from the batteries to your wind turbine. Be sure to include height of the tower. Refer to the appropriate chart for your system voltage and number of turbines and select the wire size. We recommend AWG6 multi-strand wires for 24V wind system, and AWG4 multi-strand wires for 12V system. Down-tower wire has a weight and may cause the connection loose.
To relieve the strain, t. Ie a knot at the wire after connecting. DOES NOT COVER RUST AND CORROSION.ALL CLAIMS MUST BE ACCOMPANIED WITH ORIGINAL INVOICE. ALL INSTALLATIONS MUST BE DONE BY A QUALIFIED INSTALLER.
We understand that sometimes an item may not turn out to be just what you need. Return or replacement request is available within 1 week after parcel received & in original condition and packing. Please DO NOT send without communication. Please do not forget to give us and. If you are not satisfied with your shopping Experience.We will try our best to solve any problems for you as soon as possible, thanks. We will provide you service as best as we can, cause the. Is what we are striving for. Thank you again and Have a great day!! The item "Max850WithRated600W 48V Wind Turbine Generator Windmill+ WP Controller+CFRP blades" is in sale since Tuesday, August 8, 2017. This item is in the category "Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Wind Power Supplies\Wind Turbines & Kits". The seller is "funbox6" and is located in Suzhou, Jiangsu.
This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.