Premium Material: The blades are made of Nylon fiber which is waterproof, corrosion-resistant, and lightweight, along with die-casting aluminum alloy fuselage and stainless steel fittings, making this product durable and strong. Moreover, the wire is heat-resistant and moisture-resistant, which is safe to use. Environmental-friendly: Wind power generation does not require the use of fuel, nor does it produce radiation or air pollution. High Efficiency: Controlled by MPPT intelligent microprocessor, it can effectively regulate the current and voltage(12V), and has a high utilization rate of wind energy, which contributes to the annual power generation.MPPT charge is waterproof and dustproof and can be applied to all environments and all seasons. Stable Performance: The unique magnetic circuit design makes the starting torque very small, ensuring its breeze starting ability. Moreover, the 3-phase AC permanent magnet generator and 650W maximum power help this machine reach the maximum wind speed of 60m/s. Considerate Design: The yaw adjustment system (rotating aluminum alloy fuselage and tail fin designed according to aerodynamic principle) can read the wind direction and automatically adjust the position to obtain the maximum wind energy. Modern Appearance: The round fuselage, fan-shaped blades, smooth lines, and timeless white color make this product look elegant and modern, fitting any scene.
Low Vibration&Noise: The double-groove thickened ball bearing makes it more stable with low vibration. And the 40db low noise provides a more comfortable environment. Easy to Assemble&Disassemble: With complete accessories and an English manual, you can assemble this wind turbine easily. And you can disassemble these blades for convenient storage when not in use. Easy to Clean: Because of the smooth surface with plastic spraying, you can wipe the dirt from the machine and blades with a wet cloth.
Protective Package: To prevent the product from being damaged and bumped during transportation, we packed it with foam to protect your products to the maximum extent possible. Anemometer: The equipped anemometer with MODE&SET buttons, a six-blade wind wheel, and a thermal probe allows for accurate wind speed measurement. And it's anti-slip rope ensures convenient carrying. Built-in Copper Insert: The copper insert won't damage the nylon fiber material when the bolt is tightened.
Flange Connection: The flange connection allows for a stable and firm connection between the wind turbine and the tower tube(excluded), making it safer to use. Round Edge: The round edge of the blades and generator prevents your hands from scratching during installation.It is suitable for the leisure sector, boats, gazebos, homes, RVs, cabins, and mobile homes, as well as for green windmills, corporate, and industrial energy supplements. Take out the wind turbine, put it on the tower, and align it with the flange holes.
Install four flat washers on the four bolts, and then insert the bolts into the corresponding holes of the flange. Tighten the screws with an Allen key. The three wires of the wind turbine are connected with the transmission cable, each pair of wires is not less than 30mm, and the adhesive tape at the connection end is 100mm. Connect the wind turbine cable to the controller. The battery must be connected to the controller before wiring.
Material: Nylon Fiber, Die-casting Aluminum Alloy, Neodymium Iron Boron. Wind Direction Adjustment: Automatically Adjust the Windward Angle. Generator Type: 3-Phase AC Permanent Magnet Generator. Anemometer Battery: One 3V Lithium Battery(Included).
Blade Length(Each): 40cm/15.7inch. Blade Diameter(Wheel Included): 92cm/36.22inch. Tower Tube Diameter: 42-45mm/1.65-1.77inch(Not Included). Package Size: 722823cm/30.711.029.05inch.Gross Weight: 8.2kg/18.07lbs. This package does not include a tower tube, and we recommend using a steel pipe or iron pipe of 1.65-1.77 in diameter. The wind turbine should be installed where there is strong wind or without tall buildings and obstacles.
If installing it near the obstacles, the position is better as far as possible from obstructions, or the installation height should be 20ft higher than the top of obstructions, which can make full use of the wind power. It should avoid the cliff and the turbulent region.
The power of the wind turbine will increase with the wind speed. When the wind speed is very low, the wind wheel of the wind turbine will remain stationary. When the cut-in wind speed is reached (usually 3m/s), the wind wheel starts to rotate and the generator starts to generate electricity.As the wind becomes stronger, the output power will increase. When the wind speed reaches the rated wind speed, the wind turbine will output its rated power. After that, the output power will remain roughly unchanged. When the wind speed increases further and reaches the cut-out wind speed, the wind turbine will brake without power output to avoid damage. Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement, and make sure you do not mind before you order. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it's non-workdays, please kindly be patient and wait till Monday.
Nylon Fiber, Die-casting Aluminum Alloy, Neodymium Iron Boron. Automatically Adjust the Windward Anglec. 3-Phase AC Permanent Magnet Generator. One 3V Lithium Battery(Included). 42-45mm/1.65-1.77inch(Not Included).