5 Blades 12000W DC-12V Wind Turbine Generator With Power Charge Controller

  

12000W Wind Turbine Generator Unit 5 Blades DC 12V With Power Charge Controller. Using reinforced nylon fiber on wind wheel blades , the coefficient of wind energy utilisation is increased, so as increased annual electricity generation capacity. Low start up wind speed, high efficiency, small size, low vibration.

The shell is made of stainless steel die-casting, with double bearing carrier, anti-typhoon capacity is. Hree-phase permanent magnet synchronous motor. Efficient AC generator with high performance NdFeB permanent magnet. A fully integrated voltage regulator that automatically shuts down when the battery is fully charged.

The fan is controlled by MPPT intelligent microprocessor, which. Effectively adjust current and voltage. Ith yaw adjustment system, the wind direction position is automatically read and the rotor position is adjusted to capture the maximum wind energy. The tail fin is designed according to the aerodynamic principle, with low starting speed and low vibration. For home use, For monitoring use, For. Marine use, For wind solar. Wind wheel diameter: 47.09 inch.

Blade length: 23.55 inch. Number of blades: 5 PCS. Cabin Material: Die Casting Aluminum Alloy. Generator Type: 3-Phase AC Permanent Magnet Generator. Controller brake system: Overspeedthree-phase short circuit brake.

Wind Direction Adjustment: Automatically Adjust The Windward Angle. The wind turbine is made entirely of high quality aluminum and stainless steel fittings.

The wind turbine blade is made of high quality nylon fiber with 30% carbon fiber and anti-UV anti-corrosion material, which has strong flexibility and high safety factor. The optimized starting shape design improves the wind energy utilization rate and increases the power generator.

Double bearings make it run with low vibration and quiet. It can also make wind power generation start from a low wind speed, rotate steadily and silently. Intelligent micro-processing controller effectively regulates current and voltage. The surface of the wind turbine is coated with a special process that provides excellent resistance to oxidation and corrosion under any harsh conditions, as well as excellent corrosionwater and sand resistance.

Three-phase permanent magnet synchronous motor. Efficient AC generator with high performance NdFeB permanent magnet and unique magnetic circuit designso that the starting torque is very small, can effectively ensure the wind starting capacity of the fan. The wind turbine is controlled by MPPT intelligent microprocessor, which can effectively adjust current and voltage. The machine will shuts down, when the battery is fully charged.

Take out the wind turbine, put the wind turbine on the tower and align it with the flange hole. Mount the four flat gaskets on the four bolts, then insert the bolts into the holes corresponding to the flange. Tightening the screws by hex key. The three wires of the wind turbine are connected to the transmission cable, each pair of wires is not less than 1.18 inch, and the tape at the connection end is at 3.94 inch. Connect the wind turbine's cable to the controller and the battery must be connected to the controller before wiring.

1x Wind Turbine tower tube isn't included. 1x Set Screws and Nuts. Appication: For home use, for monitoring use, For. Any further information about payments.

Our products are 100% brand new and good quality. Although we did a solid and safe packaging, it may still suffer some damage or missing during transportation, so please check the package and items before signing your name. If you are satisfied with our products and service, please leave us.

We will replay your message within 24 hours. The item "5 Blades 12000W DC-12V Wind Turbine Generator With Power Charge Controller" is in sale since Tuesday, September 28, 2021. This item is in the category "Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Wind Power Supplies\Wind Turbines & Kits".

The seller is "liuxuxiang8" and is located in Pomona, California. This item can be shipped to United States.

1. Brand: Unbranded
2. Power Source: Wind
3. Type: Wind Turbine Generator
4. Axis Orientation: Horizontal
5. Current Type: DC
6. Application: Agriculture/Farming,Home/Garden,Commercial
7. Power: 12000W
8. System Configuration: Hybrid
9. Features: High efficiency,2 Year Warranty
10. Voltage: DC12V
11. MPN: Does Not Apply
12. Number of Blades: 5
13. Wattage: 10000-12000W
14. Material: Nylon Fiber
15. Inverter Technology: Hybrid
16. Country/Region of Manufacture: China
17. Color: White
18. Custom Bundle: No
19. Rated Speed: 800r/min[RPM]
20. Tower Diameter: >80 mm(3.2in)
21. Rated Voltage: DC27-54V
22. Tower Height: 4.5m-10m(15-33in)
23. Battery Voltage: DC12V
24. Battery Capacity: 200AH-400AH
25. Start-up Wind Speed: 2.5m/s(8in/s)
26. Rated Wind Speed: 12m/S(35in/s)