10000W Max Power 5 Blades DC 12V Wind Turbine Generator Kit with Charge Controller

  
10000W 5 Blades Wind Turbines Generator Horizontal 12V Energy Turbines Charge. Using reinforced nylon fiber on wind wheel blades , the coefficient of wind energy utilisation is increased, so as increased annual electricity generation capacity.

Low start up wind speed, high efficiency, small size, low vibration. The shell is made of stainless steel die-casting, with double bearing carrier, anti-typhoon capacity is. Hree-phase permanent magnet synchronous motor.

Efficient AC generator with high performance NdFeB permanent magnet. A fully integrated voltage regulator that automatically shuts down when the battery is fully charged. The fan is controlled by MPPT intelligent microprocessor, which. Effectively adjust current and voltage.

Ith yaw adjustment system, the wind direction position is automatically read and the rotor position is adjusted to capture the maximum wind energy. The tail fin is designed according to the aerodynamic principle, with low starting speed and low vibration. For home use, For monitoring use, For. / marine use, For wind solar. Wind wheel diameter: 47.09 inch.

Blade length: 23.55 inch. Number of blades: 5 PCS. Cabin Material: Die Casting Aluminum Alloy. Generator Type: 3-Phase AC Permanent Magnet Generator. Controller brake system: Overspeedthree-phase short circuit brake. Wind Direction Adjustment: Automatically Adjust The Windward Angle. The wind turbine is made entirely of high quality aluminum and stainless steel fittings. The wind turbine blade is made of high quality nylon fiber with 30% carbon fiber and anti-UV anti-corrosion material, which has strong flexibility and high. The optimized starting shape design improves the wind energy utilization rate and increases the power generator. Double bearings make it run with low vibration and quiet. It can also make wind power generation start from a low wind speed, rotate steadily and silently. Intelligent micro-processing controller effectively regulates current and voltage. The surface of the wind turbine is coated with a special process that provides excellent resistance to oxidation and corrosion under any harsh conditions, as well as excellent corrosionwater and sand resistance. Three-phase permanent magnet synchronous motor. Efficient AC generator with high performance NdFeB permanent magnet and unique magnetic circuit designso that the starting torque is very small, can effectively ensure the wind starting capacity of the fan. The wind turbine is controlled by MPPT intelligent microprocessor, which can effectively adjust current and voltage. The machine will shuts down, when the battery is fully charged.

Take out the wind turbine, put the wind turbine on the tower and align it with the flange hole. Mount the four flat gaskets on the four bolts, then insert the bolts into the holes corresponding to the flange. Tightening the screws by hex key.

The three wires of the wind turbine are connected to the transmission cable, each pair of wires is not less than 1.18 inch, and the tape at the connection end is at 3.94 inch. Connect the wind turbine's cable to the controller and the battery must be connected to the controller before wiring. 1x Wind Turbine tower tube isn't included. 1x Set Screws and Nuts. Appication: For home use, for monitoring use, For. Marine use, For wind solar. We supply many products including computers accessories outdoor goods, sport goods, home office garden & furniture.

High product quality, reasonable prices, excellent customer service and a reliable credit standing is our tenet. We are not responsible for any wrong or undeliverable addresses. We stand behind every product we sell. Your better comments will be an encouragement for us to offer the better quality and the better service in future.

We shall try our best to solve your problem to your satisfaction. The item "10000W Max Power 5 Blades DC 12V Wind Turbine Generator Kit with Charge Controller" is in sale since Wednesday, December 15, 2021. This item is in the category "Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Wind Power Supplies\Wind Turbines & Kits".

The seller is "finerygo1" and is located in Pomona, California. This item can be shipped to United States.

1. Brand: Unbranded
2. Power Source: Wind
3. Type: Wind Turbine Generator
4. Axis Orientation: Horizontal
5. Current Type: DC
6. Application: Home/Garden
7. Features: waterproof
8. Voltage: 27-54V
9. Model: None
10. MPN: Does not Apply
11. Number of Blades: 5
12. Wattage: 10000W
13. Country/Region of Manufacture: China
14. Material: PBT
15. Color: Blue
16. Recommended Environment: Outdoor
17. Rated Wind Speed: 12m/S(35'/s)
18. Custom Bundle: No
19. Bundle Description: None
20. Battery Voltage: DC12/24V
21. Start-up Wind Speed: 2.5m/s(8'/s)
22. Rated Speed: 800r/min[RPM]
23. Tower Diameter: >80 mm(3.2")
24. Tower Height: 4.5m-10m(15-33')
25. Battery Capacity: 200AH-400AH
26. Packing Dimension: 687*365*210mm(27"x14.4"x8.3")
27. Certification: CE, RoHS, ISO9001
28. Brake Voltage: 14.5V/29V
29. Turbine Recovery voltage: 13.2V/26.4V
30. Rated panel Power: 10000W
31. Largest Discharging Current: 20A
32. Battery overcharging Protection: 16.5V/33V(Turn off Load Output)
33. Battery Discharging Protection: 10.7V/21.4V(Turn off Load Output)
34. Battery Discharge Recovery Protection: 12V/25V(Recover Load Output)
35. Static Power: 15mA
36. Working Temperature: -35~+75
37. Inbreaking Protection: IP67