Wind Turbine Generator

Missouri Wind Raptor G5 12 Volt 5 Blade Freedom 3 Sealed Wind Turbine Generator


Missouri Wind Raptor G5 12 Volt 5 Blade Freedom 3 Sealed Wind Turbine Generator
Missouri Wind Raptor G5 12 Volt 5 Blade Freedom 3 Sealed Wind Turbine Generator
Missouri Wind Raptor G5 12 Volt 5 Blade Freedom 3 Sealed Wind Turbine Generator
Missouri Wind Raptor G5 12 Volt 5 Blade Freedom 3 Sealed Wind Turbine Generator
Missouri Wind Raptor G5 12 Volt 5 Blade Freedom 3 Sealed Wind Turbine Generator
Missouri Wind Raptor G5 12 Volt 5 Blade Freedom 3 Sealed Wind Turbine Generator
Missouri Wind Raptor G5 12 Volt 5 Blade Freedom 3 Sealed Wind Turbine Generator

Missouri Wind Raptor G5 12 Volt 5 Blade Freedom 3 Sealed Wind Turbine Generator    Missouri Wind Raptor G5 12 Volt 5 Blade Freedom 3 Sealed Wind Turbine Generator
Raptor Generation 5 Freedom 3 Fully Sealed Wind Turbine. 70 Inch 5 Blade 12 Volt 1600 Watt Wind Turbine. Freedom 3 Sealed PMG - For Land or Sea. Our Missouri Freedom Wind Turbines are hot-dipped galvanized with zinc-plated hubs! Resists Rust - No need for painting or special coating for up to 50 years under normal conditions. Highly Anticipated - New for 2019, Our Freedom 3 Sealed PMG is Perfect for Marine and Desert Use or Anywhere a Wind Turbine Can Be Mounted.

Missouri Wind and Solar Freedom 3 PMG. Is fully sealed to create a water resistant motor for wind and hydro power. Ruly well thought out with years of R&D behind the production. The 7 Blade Freedom 3 has been installed in a less than ideal rooftop position at our store in Seymour, MO.

Even so, it has a startup in 6-8 MPH winds! We have even run it through our wind tunnel test at 55 MPH. The fully sealed motor is.

Perfect for marine environments but can be used anywhere a wind turbine can be mounted. Just like the Missouri Wind and Solar. The Sealed PMG contains more copper than typical PMAs on the market. More copper equals more power output!

Our custom made skewed stator reduces cogging and allows startup in lower wind speeds. Fully Sealed 1600 Watt Freedom 3 PMG. 3 phase bridge rectifier for converting to DC output. (see below for more specifics).

Heavy duty hub spacer/stabilizer with slot to fit keyway. PMG mounting bracket and heavy duty Stars & Stripes wind turbine tail.

Mounting Bracket fits on 1.5" schedule #40 or #80 pipe (1 7/8" OD) and allows for easy turning. Tail fin measures 9 3/4 inches wide x 28 3/4 inches tall. Cut from 16 gauge steel.

Hot dipped galvanized weather resistant finish. Zinc plated steel hub is 8 3/8 inch diameter and 1/4 inch thick. Black carbon fiber composite blades. Aerodynamically tapered blades for maximum output. Each blade is 33 inches long.

Assembled blades and hub makes 70 inch swept area. Overall length from blades to tail is 37 inches. No slip rings to fail or replace. Simple and effective, the turbine uses a wire tension system which will last a lifetime. The single power transmission cord never twists because the wind never spins the turbine around in the same direction hundreds of times.

Typically, the wind only comes from two directions. It has yet to be an issue with any one of the thousands of turbines we have distributed. Fully Sealed Freedom 3 PMG Features.

To withstand wear and abuse. With additional labyrinth style seal.

Case with a rough, natural finish which means. More surface area to speed cooling and improve output performance. Keyed shaft and hub stabilizer.

That bolts on to the blade hub to prevent slipping and improve safety. Hub stabilizer that channels water away. From entering through the front of the housing.

To keep water from seeping into the case. No marine varnish or painting required. 17 mm stainless steel shaft compatible with all Missouri Wind and Solar hubs and blade sets. Custom hub spacer/stabilizer with keyway and bolts for attaching to Missouri Wind and Solar blade hubs.

Zinc plated 14 rare earth neodymium magnet rotor. No brushes to fail or replace. Arge, heavy duty bearings in front and back. Fits delco bolt patterns and mounts up to our standard mounting bracket.

1 15/16 on center between mounting holes. PMA and PMG cases should not be painted or coated. This prevents heat from leaving the motor and reduces efficiency. If you have an open faced motor like our Freedom single and dual PMGs, you can marine varnish the interior components. Products may be slightly different than the ones pictured.

If our supplier runs short of the products shown, we will substitute them for the same quality or better. The item "Missouri Wind Raptor G5 12 Volt 5 Blade Freedom 3 Sealed Wind Turbine Generator" is in sale since Friday, January 18, 2019. This item is in the category "Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Wind Power Supplies\Wind Turbines & Kits". The seller is "missouriwind" and is located in Seymour, Missouri. This item can be shipped to United States, Canada, United Kingdom, Mexico, Germany, Japan, Brazil, Australia, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Greece, Portugal, Cyprus, Slovenia, Sweden, South Korea, Indonesia, Taiwan, Thailand, Belgium, Hong Kong, Ireland, Netherlands, Poland, Spain, Austria, Bahamas, Israel, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Chile, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica, Antigua and barbuda, Aruba, Belize, Dominica, Grenada, Saint kitts and nevis, Saint lucia, Montserrat, Turks and caicos islands, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Peru, Pakistan, Paraguay, Reunion, Viet nam, Uruguay.

  1. Modified Item: No
  2. Blade Material: Carbon Fiber
  3. Custom Bundle: Yes
  4. Wattage: 1600
  5. Current Type: AC/DC
  6. Axis Orientation: Horizontal
  7. EAN: Does not apply
  8. ISBN: Does not apply
  9. UPC: Does not apply
  10. Type: Wind Turbine Generator
  11. Color: Black
  12. Number of Blades: 5
  13. MPN: FREEDOM_III_G5_5B70
  14. Rotor Diameter: 70 Inches
  15. Non-Domestic Product: No
  16. Model: Raptor Generation 5
  17. Brand: Missouri Wind and Solar
  18. Application: Back-Up Power
  19. Resistance Properties: Corrosion Resistant
  20. Bundle Description: Includes wind turbine blades, blade hub, locking collar, zinc plated yaw bearing, galvanized mounting bracket, clamps, galvanized tail arms and tail fin, and the nuts and bolts for assembly.


    Missouri Wind Raptor G5 12 Volt 5 Blade Freedom 3 Sealed Wind Turbine Generator    Missouri Wind Raptor G5 12 Volt 5 Blade Freedom 3 Sealed Wind Turbine Generator