Wind Turbine Generator

800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller


800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller
800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller
800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller
800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller
800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller
800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller
800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller
800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller
800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller
800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller
800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller

800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller    800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller

800W DC 12V Wind Turbine. Connection Overview: The Wind Generator will generate AC power and is able to charge 12V batteries with a rectifier. Note: the 12V Batteries above are not included. If your home or farm is connected to the power grid, on windier days you may be able to sell excess power generated by your wind turbine to your utility. This concept is called net metering.

Even if net metering is unavailable, you might be able to reduce your power bills by using the electricity generated by wind turbines, and become less dependent on your utility. Since wind speed increases with height, increases to the tower height can mean enormous increases in the amount of electricity generated by a wind turbine. Our's - Aluminum Body, Durable and Long Lasting - Unlike rubber, PVC Rings are much more durable will not harden and crack and cause leaks - Bearing are covered and will not rust / leak.

Competitor's - Plastic Body , becomes brittle under the Sun's UV Ray - Rubber ring will harden after approximately 1 year of use and will start cracking and leaking - Bearing are exposed and will rust / leak. Nylon 6.6 + Carbon Fiber. 59.7cm (23.5 inches). Incorporates highly efficient, true airfoil - Manufactured using a precision injection molding process that produces blades of exceptional consistency. Adjustable blade degree with included degree adjusters (Shims) Increase/decrease blade angle by installing degree adjuster under the blades "+" on the right side = Increase angle = More Torque, Less Speed "-" on the right side = Decrease angle = Less Torque, More Speed Below are comparisons between the our blades and competitor's blades.

Pros - 140mm diameter, 10% larger than competitor's - High blade capacity, allow up to 6 to be installed - Covers the entire face plate to eliminate vortex. Cons - 125mm in diameter - Only allows 3 blades to be installed - Does not cover face plate completely. Ours - Dual Metal ball bearing to prevent vertical vibration - Yaw shaft diameter: 40mm - 3cm of stabilizing distance with 2 bearings - No vibration = Increase in efficiency - Reduction in noise output - One piece design Yaw body provides more stability. Competitor's - Single bearings will not eliminate vertical vibration - Yaw shaft diameter: 35mm - Stabilizing distance effectively shorten to 1.4cm with one bearing (53% reduction) - Vibration will cause bearing to grind on yaw shaft and create a bigger play, which in turn will cause more vibration in a never ending cycle - 2 pieces design Yaw body is less stable. Reduce wind resistance - Eliminates vortexes - Greater stability - Neighbor Friendly.

With Nose Cone - Smooth Performance. Without Nose Cone - Air current spins into tiny vortexes. Rotating blades present the most serious mechanical hazard. The blades may be moving at velocities over 275 miles per hour (440 km/hr). At this speed, the tip of a blade is nearly invisible and can cause serious injury. Under no circumstances should you install the turbine where a person could come in contact with moving rotor blades. The installer of these blades is solely responsible for the use or misuse of these blades. We assume no liability for ANY injuries caused by these products. NO OPERATING COST GENERATES ELECTRICITY FROM THE ABUNDANT RESOURCE. 12V 5A Charge Controller For Solar & Wind Hybrid System. 12V- 5A Solar Controller (CQ1205). 118 X 110 X 35 mm. The controller wil adjust over-discharge voltage and protected voltage according to batteries dishcarge rates.

Charge Controller - Instruction Manual. All pictures and descriptions are subjected to change without notice. We are not responsible for any inadvertent errors. Items that are used/ damaged/ deformed or altered in any ways will not be accepted.

Spams and mass e-mailing will be deleted without slightest glance. E-mails with virus or anything subjected to hacking are automatically deleted. The item "800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller" is in sale since Monday, April 17, 2017. This item is in the category "Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Wind Power Supplies\Wind Turbines & Kits". The seller is "hi_iq" and is located in Point Roberts, Washington.

This item can be shipped worldwide.

  1. MPN: n/a
  2. Brand: GreenergyStar
  3. Application: Agriculture/Farming
  4. System Configuration: Grid-Tie
  5. Voltage: 12
  6. Axis Orientation: Horizontal
  7. Current Type: AC
  8. Protection Properties: Low Voltage Protection
  9. Blade Material: Nylon Fiber
  10. Number of Blades: 3, 6
  11. Wattage: 800
  12. Color: White


800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller    800 W WATT 12 V DC 3-6 Blade Wind Turbine Generator + Charge Controller