A Grid-Tie Inverter is a device that that can transform DC electricity (ie: Solar Panels, Wind Turbine, Battery Storage) into AC power that can be directly injected into your utility's electricity network (the power grid). As of today, most inverters available in the market are in the high output (1000W 5000W) category. Their prices ranges in the thousand's range and it is just too much of an up front cost for anyone interested in green energy generation. In addition, because of the high output, a certified electrician will need to be hired to install the equipments and connect the cables.
Ever since we invented the first generation of the Micro Grid Tie Inverters, connecting to the grid has never been this easy and affordable. This is the perfect start up solution for anyone interested in green energy generation as it is affordable and maintenance free. In addition, our inverters are stackable ; meaning multiple unit of these devices can be connected in parallel to generate a higher output. It is up to us. To lead mankind into a greener future.Non- Reusable Power being consumed today. Reusable Power being generated for a better tomorrow and a brighter future. What's New in the 2nd Generation? So you ask, What's new in this second generation? Well, there are number of upgrades in performance, safety and display that are not available in the first generation or other inverters in the market. We will use our Enviro-Techs SSI-200W first generation inverter as the base model for comparison. Here are the high lights: Performance.
152 x 143 x 57 mm. 163 x 154 x 57 mm. 400W, 60% enhanced in Power Output - 38.5% better in Space Utilization. 51% better in Weight Reduction with. New Model: GP2-400 Second Generation Normal Operation.Unique and intuitive display design - LED cycling in circular formation - Represent electric meter spinning backward and power is being output to the grid - Smooth motion. Old Model: SSI-200W First Generation LED Display (reference only). 3 Green LED moving from left to right linearly - LED movement are somewhat not continuous due to the fact that motion breaks off at the last light. New Model: GP2-400 (30A External Fuse).
External 30A Fuse for easy maintenance -Utilizing low resist DC input circuit to increase efficiency. Reverse Polarity protection - Buzzer will alarm when fuse need to be replaced - Reduce internal temperature.
Old Model: SSI-200W (Internal Fuse). Hard to maintenance - Need to remove knobs and remove bottom plate - Heat generated by the fuse will stay inside the inverter. Automatic AC Voltage & Wider Voltage Range for DC input. New Model: GP2-400 (Automatic Voltage Switch).Automatically Switch between 110V 220V AC - Compatible with grids from ANY countries. No more manual switch - Avoid unit being damaged because of human mistakes - Cleaner User Interface - Wider DC Input Voltage Range 10.8V 28V - Allow MORE types of power source to be connected (ie: Air-X, 12V Battery, and etc). Old Model: SSI-200W (Manual Voltage Switch). Easy to be overlooked and cause damage to inverter - Can be troublesome when there are multiple units - Narrow DC Input Voltage Range 14V 28V -14V is a range that is too high for starting wind turbines, and half charged 12V batteries. Feature: - Grid-Tied - sell green power directly back to the grid at a premium rate (depends on your location) - Maximum Power Point Tracking (MPPT) - optimize power output - Plug and Play Design, simply plug into an outlet (GFI), no hard-wiring - 60% enhanced in power output compare to first generation inverters - 38% better in.
With higher quality parts - Unique and intuitive LED display design to reflect power output rate - External 30A Fuse for easy maintenance - Automatic 110V - 220V AC voltage switch, NO MORE manual hassle - Wider DC Input Voltage Range, from 10.8V 28V compare to 1st generation's 14V 28V - Allow MORE types of power source to be connected ie: Air-X, 12V battery, and etc. Aluminum enclosure will act as heat sink to help dissipate heat - Stackable (connect in parallel for higher output) - Island protection: Inverter will shut down during black outs. Simple and safe installation - Reverse polarity protection - Generates pure Sine Wave - Constant Power Output - Low distortion output on all ranges - Allow different Power factor from loads - Does not require rewiring of existing electronics - Compact and light weight design Installation. Install in a low humidity and well-ventilated area.
Connect the Solar Panel, Battery or Wind Turbine's DC supply cables to the DC input terminal of the inverter as shown in Figure 2. Wind Turbine installations will require respective charge controllers and dump loads. Connect the inverter to a wall socket with the supplied AC Power Cord as shown in Figure 1. Pay close attention to the polarity of your DC input. Connecting incorrectly might blow the fuse.In such case the inverter will make a buzz sound whenever power is connected and the fuse will need to be replaced. Yes, inverter shuts down during black out. DC Input Voltage (Solar & Wind).
Unlimited as long as it doesn't exceed main circuit amperage limit. 20'C - 65'C. Dimension (L x W x H). 16.3 x 15.4 x 5.7 cm 6.3" x 6.10" x 2.25. 1 Red and 6 Green LED.Any unauthorized disassembly, repair, or modification. Each Inverter can support up to. NO OPERATING COST GENERATES ELECTRICITY FROM THE ABUNDANT RESOURCE - SOLAR & WIND. All pictures and descriptions are subjected to change without notice. We are not responsible for any inadvertent errors. Items that are used/ damaged/ deformed or altered in any ways will not be accepted. Spams and mass e-mailing will be deleted without slightest glance. E-mails with virus or anything subjected to hacking are automatically deleted. The item "1600W Watt Grid Tie Inverter For Solar Panel Wind Turbine Generator" is in sale since Friday, October 1, 2010. This item is in the category "Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters". The seller is "hi_iq" and is located in Point Roberts, Washington.
This item can be shipped worldwide.