11 Raptor Generation 4 Gray Wind Turbine Generator Blades and Hub Made in USA

  

11 Raptor Generation 4 series blades. And 1/4 thick x 9 inch diameter. ZINC PLATED hub and mounting hardware. The 11 blade design is for PMAs and PMGs in extreme low wind conditions.

Massive torque and low wind start up speed. Odd number of blades have the best performance and balance.

Unbreakable, most durable, most aerodynamic. Outperforms any aluminum, plastic and wooden blades on the market, unbeatable. RAPTOR BLADES will replace many wind turbine blades and improve the performance of the turbine.

MADE IN THE U S A. RATED TO WITHSTAND 125 mph WINDS. RAPTOR SERIES BLADES ARE THE FASTEST AND QUIETEST. WIND TURBINE BLADES ON THE MARKET! Cold zinc plated no painting required! Mounting holes are 1/4'' with 15/16'' hole center to center.

17 mm hub center mounting hole. Evenly spaced cooling holes allow wind to pass through to prevent overheating of the PMA or PMG. The Raptor G4 wind turbine blades are made from revolutionary. (used by the aircraft industry) - The same material used in the F-22 Raptor fighter jet. Our Raptor Generation 4 blades can last 75 years in the sun!

Made to withstand extreme heat and sub-zero temps, our blades are designed for high speed, high efficiency, affordability and durability. They are rated to withstand 125 mph winds and are designed to operate real PMA's (permanent magnet alternators) at high speed in low winds to create the maximum power a PMA can put out. Our precision, aerodynamically tapered blades feature a 5.5 mph start up speed. Our superior Raptor Generation 4 blades can be used on AIR-X or other wind turbines to increase low wind start-up, power production, and improve safety from plastic/PVC blades.

We've tested many blades on the market and have concluded that our Raptor Generation 4 blades are hands down the best for durability, performance, aesthetics, and overall value. Raptor Generation 4 Blade Specifications.

Blades weigh approximately 1 pound each. Ran to strict specifications and procedures.

QC gauged 100% for size. Inspected for flaws and appearance at three points. Resistant to ultraviolet light (UV protected)! Will NEVER crack or degrade. Each blade is 29 long. Blade base is 6 wide. Blade tip is 1 1/8 wide.

Mounting bolt holes are 0.245" and the bolt holes are 15/16" apart center to center. They will take sub-zero winds without breaking. Are designed to operate real PMAs (permanent magnet alternators) at high speed in low winds to create the maximum power a PMA can put out. REAL PMA's OF 500 WATTS TO 2000 WATTS.

HIGH SPEED & TORQUE TO PRODUCE ANY USABLE POWER. This cannot be accomplished with heavy, slow PVC or wood blades. If you have extreme low summer time winds, this is the hub and blade set for you! High torque, extremely powerful, high speed. Products may be slightly different than the ones pictured.

If our supplier runs short of the products shown, we will substitute them for the same quality or better. The item "11 Raptor Generation 4 Gray Wind Turbine Generator Blades and Hub Made in USA" is in sale since Thursday, July 17, 2014. This item is in the category "Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Wind Power Supplies\Wind Turbines & Kits".

The seller is "missouriwind" and is located in Seymour, Missouri. This item can be shipped to United States, Canada, United Kingdom, Mexico, Germany, Japan, Brazil, Australia, Russian federation, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Greece, Portugal, Cyprus, Slovenia, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, Hong Kong, Ireland, Netherlands, Poland, Spain, Austria, Bahamas, Israel, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Chile, Colombia, Costa rica, Dominican republic, Panama, Trinidad and tobago, Guatemala, El salvador, Honduras, Jamaica, Aruba, Belize, Saint kitts and nevis, Saint lucia, Turks and caicos islands, Barbados, Ecuador, Guadeloupe, Iceland, Sri lanka, Nicaragua, Peru, Pakistan, Viet nam, Uruguay.

1. Hub Coating: Cold Zinc Plating
2. Model: Raptor Generation 4
3. Modified Item: No
4. MPN: HWB11_GRAY
5. Country/Region of Manufacture: United States
6. Custom Bundle: Yes
7. Brand: Missouri Wind and Solar
8. Blade Length: 29 Inches
9. Non-Domestic Product: No
10. EAN: Does not apply
11. Blade Material: Carbon Fiber
12. Color: Gray
13. Type: Wind Turbine Blade
14. ISBN: Does not apply
15. UPC: Does not apply
16. Material: Carbon Fiber Composite
17. Bundle Description: Wind turbine blades sold with the hub, nuts, and bolts for assembly